Yamaha WaveRunner VX 700 Service Manual Download Page 112

Page: 112 / 181

6-7

JET

PUMP

Jet pump unit

Drive shaft removal

Remove the impeller.

TIP:

Hold the impeller duct assy. in a vise
between two aluminum plates

Remove the drive shaft

TIP:

Remove the drive shaft using a press.

Remove the rear bearing.

Remove the oil seals.

TIP:

Remove the oil seals using a flat head screw-
driver.

Remove the front bearing.

TIP:

Remove the front bearing using a press.

Impeller check

Check the impeller. Replace if damaged.

Crankshaft holder 20: 90890-06552

Stopper guide plate: 90890-06501
Bearing puller assembly: 90890-06535
Stopper guide stand: 90890-06538

Driver rod L3: 90890-06652
Needle bearing attachment: 90890-06614

Summary of Contents for WaveRunner VX 700






















































































































































































Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands

Yamaha WaveRunner VX 700, Service Manual

Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands