Yamaha WaveRunner VX 700 Service Manual Download Page 156

Page: 156 / 181

HULL

HOOD

Hull and hood

8-15

Shift lever assy. check

Check the shift lever assy. Replace if
cracked or damaged.

NOTICE:

Do not

disassemble the shift lever assy.

Bushing check

Check the bushing. Replace if cracked,
damaged, or worn.

Steering arm assy. installation

Install the steering arm assy.

, nut

and plate

, and then tighten the bolt

to the specified torque.

TIP:

• Align the projection on the steering shaft

assy. with the slot on the arm.

• Align the tab

on the plate

with the por-

tion

on the steering arm assy.

• Bend a tab

along a flat side of the bolt.

Steering arm assy. bolt

16 N·m (1.6 kgf·m, 11.8 ft·lb)

Summary of Contents for WaveRunner VX 700






















































































































































































Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands

Yamaha WaveRunner VX 700, Service Manual

Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands