Yamaha WaveRunner VX 700 Service Manual Download Page 174

Page: 174 / 181

TRBL

SHTG

Troubleshooting

9-3

Symptom 1: Unstable engine idle speed, poor acceleration, poor performance, or limited
engine speed

Fuel not supplied (all
cylinders)

Fuel leakage

Check the fuel hose.

3-3

Clogged fuel filter

Replace the fuel filter.

3-3

Fuel pump malfunction

Check the fuel pump onto the car-
buretor.

4-14

Improper low speed screw
setting

Adjust the low speed screw.

4-15

Air-fuel mixture not sup-
plied

Check the reed valve.

5-15

Compression pres-
sure is low

Compression leakage

Measure the compression pres-
sure.

3-5

Check the cylinder head gasket
and cylinder head warpage.

5-17

Check the piston and piston ring for
damage.

5-22

Check the cylinder for damage.

5-19

Symptom 2

Cause

Checking step

See

page

Throttle valve does
not move properly

Throttle cable installed
incorrectly

Adjust the throttle lever free play.

3-2

Throttle valve malfunction

Check the throttle valve synchroni-
zation.

4-15

Improper throttle stop
screw setting

Adjust the throttle stop screw.

3-6

Spark plug does not
spark (some cylin-
ders)

Spark plug malfunction

Check the spark plug.

3-4

Ignition coil malfunction

Check the ignition spark.

7-5

Short, open, or loose con-
nection in ignition coil cir-
cuit

Measure the ignition coil resis-
tance.

7-6

Check the ignition coil wiring har-
ness leads for continuity.

Fuel not supplied
(some cylinders)

Improper low speed screw
setting

Adjust the low speed screw.

4-15

Improper high speed
screw setting

Adjust the high speed screw.

4-15

Air-fuel mixture not sup-
plied

Check the reed valve.

5-15

Symptom 2

Cause

Checking step

See

page

Summary of Contents for WaveRunner VX 700






















































































































































































Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands

Yamaha WaveRunner VX 700, Service Manual

Search results

Summary of Contents for WaveRunner VX 700

Reviews:

Related manuals for WaveRunner VX 700

Brands by name

Popular brands