You will need to raise the sensitivity EBS setting
(see page 43) for the operators that you want the breath
controller to affect. If you raise the EBS setting for
carrier operators, the breath controller will affect vol-
ume. If you raise the EBS setting for modulator opera-
tors, the breath controller will affect tone.
Note:
Unless the sensitivity EBS setting is raised for the
operators you want to affect, the breath controller
will have no effect.
Note:
If you do not want the breath controller to affect
volume or tone, set this to 0.
Aftertouch (pitch, amplitude, pitch bias, EC bias)
After pressing (FUNCTION), press the
below “AT” in the display.
Pressing down on the keyboard after playing a note (i.e.,
"aftertouch") can regulate the depth of vibrato, tremolo,
or wah, and also tone, volume, or pitch while playing.
Aftertouch applies equally to the entire keyboard even
if you press down on only a single key.
Press the below “ > EXIT” in the display to
return to the previous display.
(1) Pitch
Function
Set the amount of vibrato depth regulated by after-
touch.
Setting
0 – 99
Explanation
This allows you to regulate vibrato depth using aft-
ertouch. As you press down on the keyboard, the
depth of vibrato will increase. When the setting is 0,
aftertouch will have no effect, and when the setting
is 99, it will have maximum effect.
Note:
Unless the sensitivity "P Mos Sens" setting (see page
43) is raised, raising this setting will have no effect.
If you do not want to control vibrato depth using
(2) Amplitude
Function
Set the amount of tremolo or wah regulated by aft-
ertouch.
Setting
0 – 99.
Explanation
This allows you to regulate tremolo or wah using
aftertouch. As you press down on the keyboard, the
amount of tremolo or wah will increase. When the
setting is 0, aftertouch will have no effect, and when
the setting is 99, it will have maximum effect.
Note:
Unless the sensitivity AMS setting is raised, and the
AME of the appropriate operators is on, raising this
setting will have no effect (see page 43).
If you do not want to control tremolo or wah
using aftertouch, set this to 0.
(3) Pitch bias
Function
Set how aftertouch will affect pitch.
Setting
– 5 0 – + 5 0
Explanation
This allows you to directly affect the pitch using
aftertouch. When the setting is 0, aftertouch will have
no effect. When the setting is – 1– –50 aftertouch
will lower the pitch, and when the setting is + 1– + 50
aftertouch will raise the pitch. The maximum range
of pitch change is approximately ±4 octaves.
Note:
If you do not want aftertouch to affect the pitch, set
this to 0.
(4) EG bias
Function
Set how aftertouch will affect volume or tone.
Settings
0 – 99
Explanation
This allows you to affect the output level of the op-
erators using aftertouch. For a setting of 0, aftertouch
will have no effect, and for a setting of 99, it will have
maximum effect.
You will need to raise the (SENSITIVITY)
EBS setting (see page 43) for the operators that you
aftertouch, set this to 0.
want aftertouch to affect. If you raise the EBS setting
Voice Edit
53
Summary of Contents for V50
