Yamaha V150D Owner'S Manual Download Page 67

Page: 67 / 81

Trouble Recovery

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29431

Temporary action in

emergency

EMU29440

Impact damage

WARNING

EWM00870

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-

board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

Stop the engine immediately.

Inspect the control system and all com-
ponents for damage. Also inspect the
boat for damage.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

Have a Yamaha dealer inspect the out-
board motor before operating it again.

EMU29462

Replacing fuse

If the fuse has blown on an electric start
model, open the fuse holder and replace the
fuse with a new one of the proper amperage.

WARNING

EWM00630

Be sure to use the specified fuse. An in-
correct fuse or a piece of wire could allow
excessive current flow. This could cause

electric system damage and a fire hazard.

Summary of Contents for V150D


















































































Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands

Yamaha V150D, Owner'S Manual

Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands