Yamaha V150D Owner'S Manual Download Page 33 | Manualshive

Page: 33 / 81

background image

Operation

28

1.

Pour engine oil into the remote oil tank.

2.

Turn on the main switch. The Yamaha
oil injection system will automatically
feed oil from the remote oil tank to the
engine oil tank.

3.

Operate the engine normally.

CAUTION:

ECM00570

When the engine is operated for the first
time or stored for a period of time, a min-
imum of 5 liters (5.3 US qt, 4.4 Imp qt) of
oil should be kept in the remote oil tank.
Otherwise the oil-feed pump chamber will
not be filled with oil, and no oil will be

supplied.

Engine oil tank capacity:

0.9 L (0.95 US qt) (0.79 Imp.qt)

ZMU01877

«
...
31
32
33
34
35
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: Yamaha Pages: 82

Brand: Gigabyte Pages: 46

Brand: Quantum Design Pages: 77

Brand: IEI Technology Pages: 162

VECTOR 1 MOTHERBOARD

Brand: Vector Graphic Pages: 14

Brand: OLIMEX Pages: 17

MBD-X11SDV-4C-TP8F-B

Brand: Supermicro Pages: 123

Brand: Banana Pi Pages: 25

Brand: DFI Pages: 28

Brand: Lenovo Pages: 51

Brand: Toyama Pages: 48

Brand: OLIMEX Pages: 10

Brand: OLIMEX Pages: 23

Brand: Mercury Pages: 96

Brand: Mercury Pages: 120

Brand: CML Pages: 26

Brand: AZZA Pages: 49

Brand: AZZA Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands