background image

 

General information

 

10

 

EMU25711

 

Battery specifications

 

EMU25741

 

Propeller selection

 

The performance of your outboard motor will
be critically affected by your choice of propel-
ler, as an incorrect choice could adversely
affect performance and could also seriously
damage the motor. Engine speed depends
on the propeller size and boat load. If engine
speed is too high or too low for good engine
performance, this will have an adverse effect
on the engine.
Yamaha outboard motors are fitted with pro-
pellers chosen to perform well over a range
of applications, but there may be uses where
a propeller with a different pitch would be
more appropriate. For a greater operating
load, a smaller-pitch propeller is more suit-
able as it enables the correct engine speed
to be maintained. Conversely, a larger-pitch
propeller is more suitable for a smaller oper-
ating load.
Yamaha dealers stock a range of propellers,
and can advise you and install a propeller on
your outboard that is best suited to your ap-
plication.

NOTE:

 

Select a propeller which will allow the engine
to reach the middle or upper half of the oper-
ating range at full throttle with the maximum
boat load. If operating conditions such as
light boat loads then allow the engine r/min to
rise above the maximum recommended
range, reduce the throttle setting to maintain

 

the engine in the proper operating range.

For instructions on propeller removal and in-
stallation, see page 53.

 

EMU25770

 

Start-in-gear protection

 

Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is in neutral. Always select neutral
before starting the engine.

Minimum cold cranking amps (CCA/
SAE):

380.0 A 

Minimum marine cranking amps (MCA/
ABYC):

502.0 A 

Minimum reserve capacity (RC/SAE):

124 minutes 

 

1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)

ZMU04608

-

x

1

2 3

Summary of Contents for V150D


















































































Reviews: