Yamaha V150D Owner'S Manual Download Page 34

Page: 34 / 81

Operation

EMU27321

Oil level indicator operation

The various functions of the oil level system are as follows:

EMU27381

Oil level indicator

Electric start models

Oil level
warning

indicator

(digital

tachometer)

Oil level warning

indicator (analog

tachometer)

Engine oil

tank

Remote oil

tank

Remarks

Green

more than 300

(0.32 US

qt, 0.26 Imp

qt)

more than

1500 cm

(1.6

US qt, 1.31

Imp qt)

●

No refilling necessary.

Yellow

more than 300

(0.32 US

qt, 0.26 Imp

qt)

1500 cm

(1.6

US qt, 1.31
Imp qt) or less

●

Add oil; see page 27.

Red–Yellow–

Green

300 cm

(0.32

US qt, 0.26

Imp qt) or less

more than

1500 cm

(1.6

US qt, 1.31
Imp qt)

●

Check oil filter for clog-
ging.

●

Check battery cable
connection. Buzzer will
sound.

●

Engine speed is auto-
matically reduced to
about 2000 r/min.

Red

300 cm

(0.32

US qt, 0.26

Imp qt) or less

1500 cm

(1.6

US qt, 1.31
Imp qt) or less

●

Oil has not been added.

●

Buzzer will sound.

●

Engine speed is auto-
matically reduced to
about 2000 r/min.

●

Buzzer sounds in
remote control box and
engine speed is limited
to about 2000 r/min to
help conserve oil.

Summary of Contents for V150D


















































































Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands

Yamaha V150D, Owner'S Manual

Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands