Yamaha V150D Owner'S Manual Download Page 7 | Manualshive

Page: 7 / 81

background image

General information

2

EMU25261

Manufactured date label

This label is attached to the clamp bracket or
the swivel bracket.

EMU25272

Star labels

Your outboard motor is labeled with a Cali-
fornia Air Resources Board (CARB) star la-
bel. See below for a description of your

particular label.

EMU25280

One Star—Low Emission

The one-star label identifies engines that
meet the Air Resources Board’s 2001 ex-
haust emission standards. Engines meeting
these standards have 75% lower emissions
than conventional carbureted two-stroke en-
gines. These engines are equivalent to the
U.S. EPA’s 2006 standards for marine en-
gines.

EMU25290

Two Stars—Very Low Emission

The two-star label identifies engines that
meet the Air Resources Board’s 2004 ex-
haust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low-Emission engines.

1. Manufactured date label location

ZMU02896

ZMU04669

1

Manufactured:

ZMU04346

1. Star labels location

1

ZMU04668

ZMU01702

«
...
5
6
7
8
9
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: Yamaha Pages: 497

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

Brand: Sun Microsystems Pages: 74

ISL70219ASEHEV1Z

Brand: Intersil Pages: 10

EMB-APL1-A10-3350-F1-LV

Brand: Aaeon Pages: 42

Brand: MSI Pages: 92

Brand: Gigabyte Pages: 40

Brand: Supero Pages: 85

ADIS1650 PCBZSeries

Brand: Analog Devices Pages: 11

Brand: Advantech Pages: 84

GA-HA65M-D2H-B3

Brand: Gigabyte Pages: 104

Brand: Intel Pages: 86

Brand: BCM Advanced Research Pages: 9

Brand: kobi Pages: 24

Brand: CML Pages: 26

Brand: ASROCK Pages: 17

Brand: Abit Pages: 64

Brand: Terasic Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands