Yamaha V150D Owner'S Manual Download Page 17 | Manualshive

Page: 17 / 81

background image

Basic components

12

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

6. Throttle
7. Fully open

1. Neutral interlock trigger

«
...
15
16
17
18
19
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: Garelick Pages: 3

Brand: ICP Pages: 50

Brand: AOpen Pages: 101

Side-Power SEP IP Series

Brand: SLEIPNER MOTOR AS Pages: 28

Brand: Abit Pages: 72

Brand: MSI Pages: 36

Brand: Freetech Pages: 48

Brand: QDI Pages: 47

Brand: Acrosser Technology Pages: 3

X58 Classified3

Brand: EVGA Pages: 2

Brand: Seco Pages: 49

SUPERO X10DRU-X

Brand: Supermicro Pages: 109

Brand: DFI-ITOX Pages: 155

P67 PRO3 SE - ANNEXE 409

Brand: ASROCK Pages: 277

Brand: MYiR Pages: 30

Brand: MYiR Pages: 100

Brand: Intel Pages: 1

Brand: Intel Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands