Yamaha V150D Owner'S Manual Download Page 70 | Manualshive

Page: 70 / 81

background image

Trouble Recovery

65

EMU29670

Engine fails to operate

EMU29691

Ignition system malfunction

If the battery voltage is low or in the unlikely
event of an ignition system malfunction, the
engine speed may become erratic or the en-
gine may stop. In such a situation, follow the
procedure below.
1.

Remove the CDI unit cover or electrical
cover, if equipped.

2.

Disconnect the yellow cord (emergency
circuit) of the CDI unit to return to port.

WARNING

EWM00350

When the yellow cord is disconnected,
the idle and low speeds are slightly high-
er than normal. Use care when starting off

or stopping.

CAUTION:

ECM00380

Follow this procedure only in an emer-
gency and just long enough to return to

port for repairs.

EMU29740

Low oil level warning activates

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

EWM01050

Be sure to stop the engine before per-

forming this procedure.

CAUTION:

ECM00900

●

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

●

Do not use this emergency procedure

ZMU03466

ZMU03923

1. CDI unit
2. Yellow cord

1

2

ZMU03924

«
...
68
69
70
71
72
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: Abit Pages: 104

Brand: AOpen Pages: 156

Brand: Elitegroup Computer Systems Pages: 82

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

Brand: Gigabyte Pages: 100

Airborne WLNN-EK-DP55x

Brand: B&B Electronics Pages: 6

Brand: EVGA Pages: 80

WAFER-CV-N26001

Brand: IEI Technology Pages: 135

PX845EV1 Series

Brand: Albatron Pages: 56

Brand: Supero Pages: 107

Brand: IEI Technology Pages: 156

Brand: JETWAY Pages: 57

Brand: MSI Pages: 104

Brand: Micrel Pages: 10

Brand: Texas Instruments Pages: 26

Brand: Commell Pages: 49

Brand: Freescale Semiconductor Pages: 160

Brand: IEI Technology Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands