Yamaha V150D Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 81

background image

Operation

39

3.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 41.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

UP

ZMU01935

UP

DN

UP

ZMU03527

«
...
42
43
44
45
46
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: IBM Pages: 357

Brand: Xeltek Pages: 19

Brand: Biostar Pages: 49

Brand: MSI Pages: 96

Brand: Avalue Technology Pages: 82

Brand: Gigabyte Pages: 84

tps61040EVM-002

Brand: Texas Instruments Pages: 31

TB360-BTC PRO 2.0

Brand: Biostar Pages: 59

Brand: Gigabyte Pages: 81

JW-A880GMT-EXTREME

Brand: J&W Pages: 39

Brand: Biostar Pages: 32

Brand: Systium Technologies Pages: 4

Brand: BCM Pages: 3

Brand: Infineon Pages: 14

Brand: IEI Technology Pages: 12

Brand: AZZA Pages: 61

Brand: Curtis Instruments Pages: 46

PHANTOM GAMING X670E PG Lightning

Brand: ASROCK Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands