Yamaha V150D Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 81

background image

Operation

37

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

UP

ZMU03523

ZMU03449

ZMU03997

«
...
40
41
42
43
44
...
»

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Brand: ASRock Industrial Pages: 44

Brand: Gigabyte Pages: 40

TPS53355EVM-864

Brand: Texas Instruments Pages: 29

TB360-BTC PRO 2.0

Brand: Biostar Pages: 59

ISL70321SEHDEMO1Z

Brand: Intersil Pages: 9

Brand: Supermicro Pages: 111

Brand: AOpen Pages: 8

Brand: OMS Pages: 11

Brand: Gigabyte Pages: 39

Brand: MSI Pages: 92

Brand: Supero Pages: 82

Brand: Norco Pages: 55

Brand: Microchip Technology Pages: 45

Brand: Portwell Pages: 93

Brand: DFI Pages: 123

Brand: Viglen Pages: 86

Brand: Texas Instruments Pages: 16

Brand: Suzuki Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands