manualshive.com logo in svg

Yamaha V150D, Owner'S Manual

The Yamaha V150D Owner's Manual is a comprehensive guide for users of this high-performance product. With detailed instructions and diagrams, this manual ensures seamless operation and maintenance. Download it for free from our website to enhance your Yamaha V150D experience.

Share
Download
background image

 

Table of contents

 

General information .......................... 1

 

Identification numbers record ..........  1

 

Outboard motor serial number .......... 1
Key number....................................... 1

 

Emission control information ...........  1

 

North American models..................... 1
Star labels ......................................... 2

 

Safety information ...........................  3
Important labels...............................  4

 

Warning labels .................................. 4

 

Basic boating rules (Rules of the 

road) .............................................. 5

 

Steering and sailing rules and 

sound signals.................................. 5

Rules when encountering vessels .... 5
Other special situations..................... 6

 

Fueling instructions .........................  8

 

Gasoline ............................................ 9
Engine oil .......................................... 9

 

Battery requirement.........................  9

 

Battery specifications ...................... 10

 

Propeller selection.........................  10
Start-in-gear protection .................  10

 

Basic components .......................... 11

 

Main components ..........................  11

 

Remote control................................ 11
Remote control lever ....................... 12
Neutral interlock trigger ................... 12
Neutral throttle lever........................ 12
Choke switch................................... 13
Throttle friction adjuster................... 13
Engine stop lanyard switch ............. 13
Choke knob for pull type ................. 14
Main switch ..................................... 14
Power trim and tilt switch on remote 

control or tiller handle ................... 14

Power trim and tilt switch on bottom 

engine cowling .............................. 15

Trim tab with anode ........................ 15
Tilt support lever for power trim and 

tilt or hydro tilt model..................... 16

Top cowling lock lever (pull up 

type).............................................. 16

Flushing device ............................... 16
Tachometer ..................................... 17

Digital tachometer ........................... 17
Oil level indicators (three 

indicators) ..................................... 17

Oil level indicator (digital type) ........ 18
Overheat warning indicator (digital 

type) .............................................. 18

Speedometer (digital type) .............. 18
Trim meter ....................................... 19
Trim meter (digital type) .................. 19
Hour meter (digital type).................. 19
Trip meter ........................................ 20
Clock ............................................... 20
Fuel gauge ...................................... 20
Fuel warning indicator ..................... 21
Low battery voltage warning 

indicator ........................................ 21

 

Warning system ............................  21

 

Overheat warning ............................ 21
Oil level warning and oil filter 

clogging warning ........................... 22

 

Operation ......................................... 24

 

Installation.....................................  24

 

Mounting the outboard motor .......... 24

 

Breaking in engine ........................  25

 

Gasoline and engine oil mixing 

chart (50:1).................................... 25

Procedure for oil injection 

models .......................................... 25

 

Preoperation checks .....................  26

 

Fuel ................................................. 26
Oil .................................................... 26
Controls ........................................... 26
Engine ............................................. 26
Operation after a long period of 

storage .......................................... 26

 

Filling fuel and engine oil ..............  27

 

Filling fuel for models without 

a fuel joint...................................... 27

Ring Free Fuel Additive................... 27
Filling oil for oil injection models...... 27
Oil level indicator operation ............. 29

 

Operating engine ..........................  30

 

Feeding fuel .................................... 30
Starting engine ................................ 30

 

Warming up engine.......................  32

Summary of Contents for V150D


















































































Reviews:

No comments

Related manuals for V150D

Yamaha 90 Owner'S Manual preview
90
Brand: Yamaha Pages: 83
TYAN S1564 Manual preview
S1564
Brand: TYAN Pages: 64
VIA Technologies EPIA-N800 User Manual preview
EPIA-N800
Brand: VIA Technologies Pages: 76
ST NUCLEO-F207ZG User Manual preview
NUCLEO-F207ZG
Brand: ST Pages: 82
ON Semiconductor NB3N502DEVB User Manual preview
NB3N502DEVB
Brand: ON Semiconductor Pages: 8
AIC Ursa User Manual preview
Ursa
Brand: AIC Pages: 58
Texas Instruments BOOSTXL-DRV8323Rx User Manual preview
BOOSTXL-DRV8323Rx
Brand: Texas Instruments Pages: 28
ASROCK IMB-390-D Settings Manual preview
IMB-390-D
Brand: ASROCK Pages: 2
Supermicro X10DRG-O+-CPU User Manual preview
X10DRG-O+-CPU
Brand: Supermicro Pages: 125
Gigabyte GA-H110M-S2 User Manual preview
GA-H110M-S2
Brand: Gigabyte Pages: 38
IEI Technology JUKI-6770 User Manual preview
JUKI-6770
Brand: IEI Technology Pages: 53
AOpen AK77-400 Online Manual preview
AK77-400
Brand: AOpen Pages: 125
Texas Instruments TPS36Q1EVM User Manual preview
TPS36Q1EVM
Brand: Texas Instruments Pages: 24
ECS PN1 SLI2 Extreme User Manual preview
PN1 SLI2 Extreme
Brand: ECS Pages: 62
ASROCK B150 Pro4/3.1 Manual preview
B150 Pro4/3.1
Brand: ASROCK Pages: 139
DFI SB102-D User Manual preview
SB102-D
Brand: DFI Pages: 59
ASROCK PE PRO User Manual preview
PE PRO
Brand: ASROCK Pages: 26
Asus P2L97-S User Manual preview
P2L97-S
Brand: Asus Pages: 68

Brands by name

Popular brands

Load more brands