Yamaha V150D Owner'S Manual Download Page 21

Page: 21 / 81

Basic components

EMU26340

Tilt support lever for power trim and
tilt or hydro tilt model

To keep the outboard motor in the tilted up
position, lock the tilt support lever to the
clamp bracket.

EMU26382

Top cowling lock lever (pull up type)

To remove the engine top cowling, pull up
the lock lever(s) and lift off the cowling.
When installing the cowling, check to be sure
it fits properly in the rubber seal. Then lock
the cowling by moving the lever(s) down-
ward.

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 43.

1. Trim tab
2. Bolt
3. Cap

1. Tilt support lever

ZMU02525

ZMU01863

ZMU03979

1. Top cowling lock lever(s)

ZMU03904

ZMU03905

Summary of Contents for V150D


















































































Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands

Yamaha V150D, Owner'S Manual

Search results

Summary of Contents for V150D

Reviews:

Related manuals for V150D

Brands by name

Popular brands