Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 40 / 96

background image

OPERATION AND IMPORTANT RIDING POINTS

5-3

5

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

NOTE:

Always shift gears at the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (16 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16720

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17071

0–1000 km (0–600 mi)

Avoid prolonged operation above 1/3
throttle.

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 1/2
throttle.

Shift up points:

1st

→

2nd: 20 km/h (13 mi/h)

2nd

→

3rd: 30 km/h (19 mi/h)

3rd

→

4th: 40 km/h (25 mi/h)

4th

→

5th: 50 km/h (31 mi/h)

Shift down points:

5th

→

4th: 25 km/h (16 mi/h)

4th

→

3rd: 25 km/h (16 mi/h)

3rd

→

2nd: 25 km/h (16 mi/h)

2nd

→

1st: 25 km/h (16 mi/h)

U29S10E0.book Page 3 Friday, May 18, 2007 1:53 PM

«
...
38
39
40
41
42
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: N-Com Pages: 2

Brand: N-Com Pages: 64

Brand: Razor Pages: 2

Brand: hepco & becker Pages: 4

Brand: Ohlins Pages: 8

Brand: KSR Moto Pages: 51

Brand: Honda Pages: 127

Brand: N-Com Pages: 32

REACTOR 40 KICKER SUZUKI ADAPTER

Brand: Garmin Pages: 40

Brand: Malaguti Pages: 383

Brand: hepco & becker Pages: 2

Brand: Saddlemen Pages: 6

Brand: Yamaha Pages: 42

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 84

NMAX GPD155 2020

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands