Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 72 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

6

EAU24321

Replacing a license plate light
bulb

1. Remove the license plate light unit

by removing the nuts, washers and
rubber dampers.

2. Remove the license plate light lens

by removing the nuts and washers.

3. Remove the defective bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the license plate light lens

by installing the washers and the
nuts.

6. Install the license plate light unit by

installing the rubber dampers,
washers and the nuts.

EAU24350

Supporting the motorcycle

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

1. Nut

2. Washer
3. Rubber damper

4. License plate light unit

1. Nut
2. Washer

3. Bulb

4. License plate light lens

U29S10E0.book Page 31 Friday, May 18, 2007 1:53 PM

«
...
70
71
72
73
74
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Yamaha Pages: 860

Brand: hepco & becker Pages: 4

Brand: R&G Pages: 12

Brand: hepco & becker Pages: 5

Brand: Parweld Pages: 4

Brand: KTM Pages: 163

Brand: SSR Motorsports Pages: 39

Brand: Suzuki Pages: 89

Brand: Yamaha Pages: 98

Star XVS13CB(C)

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 145

ROADLINER XV19SW

Brand: Yamaha Pages: 444

Brand: Yamaha Pages: 494

Brand: Yamaha Pages: 94

Brand: hepco & becker Pages: 4

Brand: CyClone Pages: 24

Brand: R&G Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands