Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 82 / 96

background image

CONSUMER INFORMATION

9-1

9

EAU26351

Identification numbers

Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.
KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION
NUMBER:

MODEL LABEL INFORMATION:

EAU26381

Key identification number

The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.

EAU26400

Vehicle identification number

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro-
vided.

NOTE:

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor-
cycle with the licensing authority in your
area.

1. Key identification number

1. Vehicle identification number

U29S10E0.book Page 1 Friday, May 18, 2007 1:53 PM

«
...
80
81
82
83
84
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Scout 25L Pannier Kit V2.0

Brand: MOSKO MOTO Pages: 13

Brand: Cake Pages: 12

Brand: NEO TOOLS Pages: 8

Brand: Memphis Shades Pages: 2

Brand: rizoma Pages: 16

Brand: hepco & becker Pages: 5

Brand: X-lite Pages: 96

Brand: yasuni Pages: 9

Brand: hepco & becker Pages: 3

Brand: DYNATEK Pages: 4

ZIEGER 10005243

Brand: IBEX Pages: 4

Brand: Faller Pages: 8

Brand: Yamaha Pages: 5

1985 XV700 Virago

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands