Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 57 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-16

6

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU22011

Accessories and replacement
parts

WARNING

EWA10621

This vehicle is not designed to pull a
trailer or to be attached to a sidecar.
The accessories or replacement
parts you choose for your vehicle
should be designed specifically for
this model, and they must be se-
curely mounted to maintain the in-
herent stability of the original
design. Genuine Yamaha Parts and
Accessories are designed and test-
ed to be compatible with your vehi-
cle. Please consider Genuine
Yamaha Parts and Accessories be-
fore making a purchase. Use of non-
Yamaha-approved accessories or
replacement parts may cause loss of
handling stability and riding safety.
Since Yamaha cannot control the
quality of accessories or parts man-
ufactured by other companies,
Yamaha cannot be held liable for

U29S10E0.book Page 16 Friday, May 18, 2007 1:53 PM

«
...
55
56
57
58
59
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Yukon Trail Pages: 21

SIDE FORCE 445cc

Brand: Mash Pages: 27

Brand: VIKING BAGS Pages: 2

Brand: Sachs Bikes Pages: 71

Brand: Lakeland Pages: 16

Brand: B&G electronics Pages: 5

Brand: GAS GAS Pages: 150

Brand: Suzuki Pages: 26

Brand: Crivit Pages: 58

2006 G 650 Xmoto

Brand: BMW Pages: 132

Brand: Blata Pages: 17

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

TDM850'99 4TX-AE3

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 105

Brand: Yamaha Pages: 111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands