Yamaha STAR XV19CSX Owner'S Manual Download

Page: 41 / 96

OPERATION AND IMPORTANT RIDING POINTS

5-4

CAUTION:

ECA10891

After 1000 km (600 mi) of operation,
the engine oil and transfer case oil
must be changed, and the oil filter
cartridge or element replaced.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

CAUTION:

ECA10270

If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.

EAU17212

Parking

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10310

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.

CAUTION:

ECA10380

Never park in an area where there
are fire hazards such as grass or
other flammable materials.

U29S10E0.book Page 4 Friday, May 18, 2007 1:53 PM

Summary of Contents for STAR XV19CSX

































































































Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands

Yamaha STAR XV19CSX, Owner'S Manual

Search results

Summary of Contents for STAR XV19CSX

Reviews:

Related manuals for STAR XV19CSX

Brands by name

Popular brands