Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 59 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-18

6

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22430

Front brake pads

Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear

indicator grooves have almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 0.8 mm (0.03 in),
have a Yamaha dealer replace the
brake pads as a set.

EAU38630

Checking the brake and clutch
fluid levels

Front brake

Rear brake

1. Brake pad wear indicator groove

1. Lining thickness

1. Minimum level mark

1. Minimum level mark

U29S10E0.book Page 18 Friday, May 18, 2007 1:53 PM

«
...
57
58
59
60
61
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Sachs Bikes Pages: 83

McPherson Strut MIR 1G00

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Happy Trails Pages: 4

Brand: Cake Pages: 12

Brand: Vance and hines Pages: 5

Brand: Honda Pages: 127

WOLVERINE X4 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 224

Brand: Yamaha Pages: 343

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 432

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 694

Brand: Yamaha Pages: 864

Brand: Yamaha Pages: 912

Brand: Yamaha Pages: 864

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands