Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 66 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-25

6

EAU23290

Checking the wheel bearings

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

EAU44572

Battery

This model is equipped with a sealed-
type (MF) battery, which does not re-
quire any maintenance. There is no
need to check the electrolyte or to add
distilled water.

To access the battery

1. Remove the rider seat. (See page

2. Unhook the battery band, and then

remove the battery cover.

3. Turn the ECU (Electronic Control

Unit) over to move it away from the
wire harness protective cover as
shown.

4. Open the wire harness protective

cover, pull the wire harness for-
ward, away from the battery, and
then remove the cover by sliding it
out from under the wire harness in
the direction shown.

1. Battery band

2. Battery cover

2

1

1. Wire harness protective cover
2. ECU (Electronic Control Unit)

2

1

U29S10E0.book Page 25 Friday, May 18, 2007 1:53 PM

«
...
64
65
66
67
68
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Kabuto Pages: 25

Brand: Memphis Shades Pages: 2

Brand: Gentex Pages: 15

V 7 CAFE CLASSIC

Brand: MOTO GUZZI Pages: 147

Light Bee QL3000DY

Brand: Surron Pages: 18

Brand: National Cycle Pages: 2

Brand: Honda Pages: 4

Brand: hepco & becker Pages: 3

Brand: Yamaha Pages: 39

Roadliner XV1900AV

Brand: Yamaha Pages: 86

ROADLINER XV19C

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 70

Road Star XV1600AT 2004

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 72

Road Star XV17ASX

Brand: Yamaha Pages: 110

Road Star XV1600A 2000

Brand: Yamaha Pages: 103

Road Star XV16AMC

Brand: Yamaha Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands