Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 24 / 96

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-7

3

EAU41700

The engine trouble warning light will
come on when the key is turned to “ON”
and the start switch is pushed, but this
does not indicate a malfunction.

EAU44600

“SELECT” switch

This switch is used to perform selec-
tions in the odometer, tripmeter, to set
the clock and to set the brightness
mode of the multi-function meter unit.
See “Multi-function meter unit” on page
3-2 for detailed information.

EAU12820

Clutch lever

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-15.)

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

1. Clutch lever

1. Shift pedal

U29S10E0.book Page 7 Friday, May 18, 2007 1:53 PM

«
...
22
23
24
25
26
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Kappa Pages: 4

Brand: UNIT 1 Pages: 23

Brand: Kabuto Pages: 16

Brand: Öhlins Pages: 8

prodrive SUR 3A00

Brand: Öhlins Pages: 4

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 4

Yamaha X-MAX 300

Brand: BRUUDT Pages: 7

Brand: Saddlemen Pages: 3

Brand: Honda Pages: 158

WOLVERINE X4 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 224

Brand: Yamaha Pages: 343

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 432

Brand: Yamaha Pages: 404

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands