Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 36 / 96

background image

PRE-OPERATION CHECKS

4-2

4

EAU15605

Pre-operation check list

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.

Engine oil

• Check oil level in oil tank.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

Transfer case oil

• Check vehicle for oil leakage.

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Rear brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Clutch

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check fluid level in reservoir.
• If necessary, add recommended fluid to specified level.
• Check hydraulic system for leakage.

Throttle grip

• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

U29S10E0.book Page 2 Friday, May 18, 2007 1:53 PM

«
...
34
35
36
37
38
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Suzuki Pages: 59

VIKING 3250D FGS

Brand: Lincoln Electric Pages: 56

Brand: Honda Pages: 60

Splendor Pro CLASSIC

Brand: HERO Pages: 56

Brand: PIAGGIO Pages: 275

Liberty 50 Catalyzed 2019

Brand: PIAGGIO Pages: 62

Brand: Hudora Pages: 8

Brand: Dynafit Pages: 48

Brand: R&G Pages: 6

Brand: VOR Motore Pages: 220

Brand: Shark Pages: 28

Brand: FMF Pages: 4

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 162

Brand: Yamaha Pages: 251

Brand: Benelli Pages: 243

Brand: Benelli Pages: 392

Brand: Kinroad Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands