Yamaha STAR XV19CSX Owner'S Manual Download | Manualshive

Page: 58 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

6

any consequences caused by the
use of items which have not been
approved by Yamaha.

EAU22072

Clutch lever

Since this model is equipped with a hy-
draulic clutch, adjusting the clutch lever
free play is not needed. However, it is
necessary to check the clutch fluid level
and check the hydraulic system for
leakage before each ride. If the clutch
lever free play does become excessive,
and shifting becomes rough or clutch
slippage occurs, causing poor acceler-
ation, there may be air in the clutch sys-
tem. If there is air in the hydraulic
system, have a Yamaha dealer bleed
the system before operating the motor-
cycle.

EAU22270

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

1. Rear brake light switch

2. Rear brake light switch adjusting nut

U29S10E0.book Page 17 Friday, May 18, 2007 1:53 PM

«
...
56
57
58
59
60
...
»

Summary of Contents for STAR XV19CSX

































































































Reviews:

No comments

Related manuals for STAR XV19CSX

Brand: Ducati Pages: 128

Brand: Honda Pages: 224

TXT PRO - PART LIST 2005

Brand: GAS GAS Pages: 38

Brand: AC Schnitzer Pages: 44

80 MasterGuard (L+K)

Brand: SCHUBERTH Pages: 44

Brand: Fantic Pages: 153

Brand: Yamaha Pages: 5

1985 XV700 Virago

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 100

2007 V Star XVS650AW

Brand: Yamaha Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands