Yamaha RX10RL Page 86 Owner'S Manual Download

Page: 86 / 99

8-33

ESU04632

Replacing a fuse

WARNING

Be sure to use the specified fuse. A wrong fuse
could cause electrical system damage or A FIRE
HAZARD.

CAUTION:

Be sure to turn the main switch to “OFF” and discon-
nect the negative battery lead to prevent accidental
short-circuiting.

1. Remove the shroud, the left and right side covers,

and the top cover. (See pages 8-5–8-7 for removal
procedures.)

2. Remove the headlight unit bolts

, disconnect the

headlight couplers and speedometer coupler, and
then remove the headlight unit.

3. Unhook the latch

and disconnect the air tempera-

ture sensor coupler

4. Loosen the joint clamp screws

5. Slide the clamps

away from the air filter case, and

then disconnect the crankcase breather hose

and

the bypass air hose

6. Slide the clamp

down, and then disconnect the air

filter case drain hose

7. Remove the air filter case.
8. Disconnect the negative battery lead.

U8FP10.book Page 33 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands