Yamaha RX10RL Page 39 Owner'S Manual Download

Page: 39 / 99

6-7

ESU00093

Brake fluid leakage

Apply the brake for a few minutes. Check to see if any
brake fluid leaks out from the brake hose joints or the
master cylinder.

WARNING

If brake fluid leakage is found, ask a Yamaha dealer
for immediate repairs.

CAUTION:

Brake fluid may deteriorate painted surfaces or plas-
tic parts. Never spill any brake fluid. If any is spilled,
clean it up immediately.

ESU04520

V-belt

Check the V-belt.

1. Remove the shroud and the left side cover, and then

remove the drive guard. (See pages 8-5–8-7 for
removal procedures.)

2. Check the V-belt for wear and damage. Replace if

necessary.

3. Install the left side cover and the shroud.

WARNING

●

Make sure that the drive guard is installed
securely before operating the snowmobile.

●

Never run the engine with the V-belt or drive
guard removed.

ESU00096

Drive guard

Check the drive guard mounts for damage. Make sure
that the drive guard is firmly in place.

Wear limit

: 32.5 mm (1.28 in)

U8FP10.book Page 7 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands