Yamaha RX10RL Owner'S Manual Download

Page: 52 / 99

7-9

CAUTION:

Do not shift from “FWD” to “REV” or from “REV” to
“FWD” while the snowmobile is moving. Otherwise,
the drive system could be damaged.

NOTE:

The reverse buzzer beeps while the shift lever is in
reverse.

2. Release the parking brake by moving the parking

brake lever to the right.

3. Press the throttle lever slowly to move the snowmo-

bile.

4. Turn the handlebar in the desired direction.
5. Squeeze the brake lever to stop the snowmobile.
6. Apply the parking brake by moving the parking brake

lever to the left.

ESU00136

Stopping the engine

Turn the main switch to the “OFF” position to stop the
engine.

“OFF”

WARNING

●

Push down the engine stop switch to stop the
engine in an emergency.

●

Make sure that the key is removed from the main
switch whenever the operator leaves the snow-
mobile, to prevent accidental starting.

U8FP10.book Page 9 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands