manualshive.com logo in svg

Yamaha RX10RL, Owner'S Manual

The Yamaha RX10RL Owner's Manual is available for free download from manualshive.com. This comprehensive manual provides users with detailed instructions and information on operating and maintaining their Yamaha RX10RL model. Gain crucial insights and maximize the functionality of your Yamaha RX10RL with this downloadable manual.

Share
Download
background image

8-14

14. Install the bottom panel and the lower right side

cover, and then install the right side cover and the
shroud.

CAUTION:

@ 

If oil is leaking or the oil level warning indicator
comes on when the engine is running, immediately
turn the engine off and have a Yamaha dealer check
the snowmobile. Continuing to operate the engine
under such conditions could cause severe engine
damage. 

@ 

ESU04571 

Cooling system

Bleeding the cooling system

WARNING

@ 

●

Do not remove the coolant reservoir cap when
the engine is hot. Scalding hot fluid and steam
may be blown out under pressure, which could
cause serious injury. 
When the engine has cooled, place a thick rag or
towel over the coolant reservoir cap, and slowly
rotate the cap counterclockwise to the detent.
This procedure allows any residual pressure to
escape. When the hissing sound has stopped,
press down on the cap while turning counter-
clockwise and remove it. 

●

The cooling system must be bled of air if the
coolant reservoir becomes empty, if air can be
seen in the cooling system, or if there is a cooling
system leak. Consult a Yamaha dealer. 

@

1

Coolant reservoir 

2

Coolant reservoir cap

CAUTION:

@ 

Operating the engine with an improperly bled cool-
ing system can cause overheating and severe
engine damage. 

@

U8FP10.book  Page 14  Thursday, April 28, 2005  5:11 PM

Summary of Contents for RX10RL




































































































Reviews:

No comments

Related manuals for RX10RL

Brands by name

Popular brands

Load more brands