Yamaha RX10RL Owner'S Manual Download

Page: 31 / 99

5-12

CAUTION:

●

Do not use accessories requiring more than the
maximum rated capacity for the auxiliary DC jack.
This may overload the circuit and cause the fuse
to blow. (See pages 8-33–8-34 for the specified
amperage.)

●

Do not use an automotive cigarette lighter or
other accessory with a plug that gets hot
because the jack can be damaged.

ESU04730

Shroud and covers

Securely fasten the shroud and covers before operating
the snowmobile. (See pages 8-5–8-7 for removal and
installation procedures.)

Shroud

Right side cover

Left side cover

Top cover

WARNING

●

Do not drive the snowmobile with the shroud or
covers unfastened or removed.

●

Keep your body and clothing away from rotating
parts when servicing the snowmobile with the
shroud or covers removed.

●

Do not touch the hot muffler and engine during or
immediately after operation.

CAUTION:

Make sure that all cables, leads, etc., are in place
when installing the shroud and covers.

Maximum rated capacity:

DC 12 V, 2.5 A (30 W)

U8FP10.book Page 12 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands