manualshive.com logo in svg

Yamaha RX10RL, Owner'S Manual

The Yamaha RX10RL Owner's Manual is available for free download from manualshive.com. This comprehensive manual provides users with detailed instructions and information on operating and maintaining their Yamaha RX10RL model. Gain crucial insights and maximize the functionality of your Yamaha RX10RL with this downloadable manual.

Share
Download
background image

8-21

1. Loosen the locknut 

1

 and the adjusting bolt 

2

. 

2. Loosen the cable locknut 

3

. 

3. Turn the cable adjuster 

4

 in or out to adjust the cable

length.

4. Tighten the cable locknut.
5. Turn the adjusting bolt in or out to adjust the clear-

ance between the parking brake pads 

5

 and the

brake disc 

6

.

6. Tighten the locknut.

ESU00180 

Checking the brake fluid level

Place the snowmobile on a level surface. Check that the
brake fluid is above the lower level and replenish when
necessary.

1

Lower level

WARNING

@ 

Be careful that water does not enter the master cylin-
der when refilling. Water will significantly lower the
boiling point of the fluid and may result in vapor
lock. 
If the brake fluid level goes down, consult a Yamaha
dealer. 

@

CAUTION:

@ 

Brake fluid may deteriorate painted surfaces or plas-
tic parts. Never spill any fluid. If any is spilled, clean
it up immediately. 

@

Cable length 

a

: 43.5–46.5 mm (1.713–1.831 in)

Clearance 

b

 + 

c

: 1.5–2.0 mm (0.059–0.079 in)

Specified brake fluid: DOT 4

U8FP10.book  Page 21  Thursday, April 28, 2005  5:11 PM

Summary of Contents for RX10RL




































































































Reviews:

No comments

Related manuals for RX10RL

Brands by name

Popular brands

Load more brands