Yamaha RX10RL Owner'S Manual Download

Page: 40 / 99

6-8

ESU00097

Drive track

Check the drive track for deflection, wear, or damage.
Adjust or replace if necessary. (See pages 8-27–8-29 for
more details.)

WARNING

Do not operate the snowmobile if you find damage to
the drive track, or if it has been maladjusted. Drive
track damage or failure could result in loss of brak-
ing ability and snowmobile control, which could
cause an accident.

ESU00982

Slide runners

Check the slide runners for wear and damage.
If the slide runners reach the wear limit, they should be
replaced.

Slide runners

Wear limit

CAUTION:

Ride on fresh snow frequently. Operating on ice or
hard packed snow will rapidly wear the slide runners.

Wear limit height:

10.5 mm (0.41 in)

U8FP10.book Page 8 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands