manualshive.com logo in svg

Yamaha RX10RL, Owner'S Manual

The Yamaha RX10RL Owner's Manual is available for free download from manualshive.com. This comprehensive manual provides users with detailed instructions and information on operating and maintaining their Yamaha RX10RL model. Gain crucial insights and maximize the functionality of your Yamaha RX10RL with this downloadable manual.

Share
Download
background image

8-17

1. Remove the shroud and the left side cover. (See

pages 8-5–8-7 for removal procedures.) 

2. Remove the drive guard. 
3. Rotate the secondary sliding sheave clockwise 

1

and push 

2

 it so that it separates from the secondary

fixed sheave. 

4. Pull 

3

 the V-belt up over the secondary fixed sheave. 

5. Remove the V-belt from the secondary sheave

assembly and primary sheave assembly. 

6. Temporarily install the new V-belt on the secondary

sheave assembly only, and then measure the V-belt
position. Do not force the V-belt between the
sheaves; the secondary sliding and fixed sheaves
must touch each other.

Standard V-belt position 

a

: 

From 1.5 mm (0.06 in) above the edge of the second-
ary sheave assembly to 0.5 mm (0.02 in) below the 
edge.

U8FP10.book  Page 17  Thursday, April 28, 2005  5:11 PM

Summary of Contents for RX10RL




































































































Reviews:

No comments

Related manuals for RX10RL

BOMBARDIER Safari 377 1988 Operator'S Manual preview
Safari 377 1988
Brand: BOMBARDIER Pages: 58

Brands by name

Popular brands

Load more brands