Yamaha RX10RL Owner'S Manual Download

Page: 75 / 99

8-22

ESU01811

Changing the brake fluid

Brake fluid replacement is necessary when the following
components are replaced during the periodic mainte-
nance or if they are damaged or leaking.

a. All oil seals of the master cylinder and caliper cylinder

b. The brake hose

WARNING

Make sure that the brake fluid and the above parts
are replaced by a Yamaha dealer.

ESU00183

Suspension

The suspension can be adjusted to suit rider preference.
A softer setting, for example, may provide greater rider
comfort, while a harder setting may allow more precise
handling and control over certain types of terrain or riding
conditions.

WARNING

Be sure to have a Yamaha dealer make this adjust-
ment.

ESU04821

Adjusting the ski spring preload

The spring preload can be adjusted by turning the spring
preload adjuster

For RX10RT/RX10R/RXW10

CD-11E

NOTE:

For RX10RTR:
To adjust the shock absorbers, refer to the separate
shock absorber owner’s manual.

Spring seat length*

Standard

Increased

←

→

Decreased

Preload

Harder

←

→

Softer

Length

Maximum
144.5 mm
(5.69 in)

134.5 mm

(5.30 in)

Minimum
134.5 mm
(5.30 in)

∗

The spring seat length changes approximately 1.5 mm (0.06 in) with
each full turn of the adjuster.

U8FP10.book Page 22 Thursday, April 28, 2005 5:11 PM

Summary of Contents for RX10RL




































































































Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands

Yamaha RX10RL, Owner'S Manual

Search results

Summary of Contents for RX10RL

Reviews:

Related manuals for RX10RL

Brands by name

Popular brands