Yamaha grizzly 700 Owner'S Manual Download

Page: 121 / 170

8-32

4. Install the drain bolt and its new gasket, and

then tighten the bolt to the specified torque.

5. Refill with the recommended differential gear

oil to the brim of the filler hole as shown.

NOTICE:

Be sure no foreign material en-

ters the differential gear case.

[ECB00411]

6. Check the oil filler bolt gasket for damage, and

replace it if necessary.

7. Install the oil filler bolt and its gasket, and then

tighten the bolt to the specified torque.

1. Differential gear oil drain bolt

2. Gasket

Tightening torque:

Differential gear oil drain bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

1. Differential gear oil filler bolt

2. Gasket

3. Differential gear oil
4. Correct oil level

Recommended differential gear oil:

See page 10-1.

Tightening torque:

Differential gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1 2

U1DT60E0.book Page 32 Wednesday, March 3, 2010 2:51 PM

Summary of Contents for grizzly 700











































































































































































Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands

Yamaha grizzly 700, Owner'S Manual

Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands