manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 122

8-33

8

8. Check the differential gear case for oil leak-

age. If oil is leaking, check for the cause.

EBU23470

Coolant 

The coolant level should be checked before each
ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.

EBU27125

To check the coolant level

1. Place the ATV on a level surface.

TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.

2. Check the coolant level in the coolant reser-

voir.

TIP

The coolant should be between the minimum and
maximum level marks.

3. If the coolant is at or below the minimum level

mark, remove panel D to access the coolant
reservoir. (See page 8-10.)

4. Remove the coolant reservoir cap, add cool-

ant or distilled water to the maximum level
mark, install the reservoir cap, and then install
the panel. 

NOTICE:

 If coolant is not avail-

able, use distilled water or soft tap water
instead. Do not use hard water or salt wa-
ter since they are harmful to the engine. If
water has been used instead of coolant, re-
place it with coolant as soon as possible,
otherwise the cooling system will not be

1. Maximum level mark
2. Minimum level mark

U1DT60E0.book  Page 33  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands