Yamaha grizzly 700 Owner'S Manual Download

Page: 162 / 170

10-3

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

Clutch:

Clutch type:

Wet, centrifugal automatic

Transmission:

Primary reduction system:

V-belt

Secondary reduction system:

Shaft drive

Secondary reduction ratio:

41/21

24/18

33/9 (9.544)

Transmission type:

V-belt automatic

Operation:

Left hand operation

Reverse gear:

23/14

28/23 (2.000)

Low range:

31/16 (1.938)

High range:

31/27 (1.148)

Chassis:

Frame type:

Steel tube frame

Caster angle:

5.0 °

Trail:

26.0 mm (1.02 in)

Front tire:

Type:

Tubeless

Size:

AT25 x 8-12

Manufacturer/model:

YFM700FAPA CHENG SHIN/C828-4P
YFM7FGPA DUNLOP/KT421
YFM7FGPHA DUNLOP/KT421
YFM7FGPSEA DUNLOP/KT421

Rear tire:

Type:

Tubeless

Size:

AT25 x 10-12

Manufacturer/model:

YFM700FAPA CHENG SHIN/C828-4P
YFM7FGPA DUNLOP/KT425
YFM7FGPHA DUNLOP/KT425
YFM7FGPSEA DUNLOP/KT425

Loading:

Maximum loading limit:

220.0 kg (485 lb)
(Total weight of rider, cargo, accessories, and tongue)

Tire air pressure (measured on cold tires):

Recommended:

Front:

35.0 kPa (0.350 kgf/cm², 5.0 psi)

Rear:

30.0 kPa (0.300 kgf/cm², 4.4 psi)

U1DT60E0.book Page 3 Wednesday, March 3, 2010 2:51 PM

Summary of Contents for grizzly 700











































































































































































Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands

Yamaha grizzly 700, Owner'S Manual

Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands