manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 147

8-58

8

To install the battery

TIP

Be sure the battery is fully charged.

1. Place the battery in its compartment.
2. Connect the positive battery lead first, then

connect the negative battery lead by installing
their bolt.

NOTICE:

 When installing the bat-

tery, the main switch must be off, and the
positive lead must be connected before
the negative lead.

 [ECB01110]

3. Install the battery holding plate by installing

the nuts.

4. Install the front carrier by installing the bolts

and tightening them to the specified torques.

5. Install the panel.

1. Positive battery lead (red)

2. Negative battery lead (black)

1

2

Tightening torques:

Carrier bolt (top):

26 Nm (2.6 m·kgf, 19 ft·lbf)

Carrier bolt (under the fenders):

7 Nm (0.7 m·kgf, 5.1 ft·lbf)

U1DT60E0.book  Page 58  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands