manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 70

7-4

7

Apparel

Always wear the following to reduce risk of injury in
an accident:

●

Approved motorcycle helmet that fits properly

●

Eye protection (goggles, helmet face shield, or
protective eyewear)

●

Over-the-ankle boots, gloves, long-sleeved shirt
or jacket, and long pants

An approved helmet and other personal protective
equipment can reduce the severity of injuries in an
accident. 

WARNING! Operating without an ap-

proved motorcycle helmet increases your
chances of a severe head injury or death in the
event of an accident.

 [EWB01411]

Wear eye protection when operating your ATV to
reduce the risk of a serious accident or injury. Eye
protection, such as a face shield or goggles, may
reduce the risk of foreign material getting in your
eyes and help prevent loss of vision. 

WARNING!

Operating without eye protection can result in
an accident and increases your chances of a
severe injury in the event of an accident.

[EWB02611]

U1DT60E0.book  Page 4  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands