manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 130

8-41

8

8. Check the sponge material and replace it if

damaged.

9. Apply Yamaha foam air filter oil or other qual-

ity foam air filter oil to the sponge material.

TIP

The sponge material should be wet but not drip-
ping.

10. Install the mesh and the sponge material into

the air filter case. 

NOTICE:

 Make sure that

the air filter element is properly seated in
the air filter case. Never operate the engine
with the air filter element removed. This
will allow unfiltered air to enter the engine,
causing rapid engine wear and possible

engine damage. Additionally, operation
without the air filter element will affect the
fuel injection system with subsequent
poor performance and possible engine
overheating.

 [ECB00761]

11. Insert the projections on the air filter case cov-

er into the holders on the air filter case, and
then install the air filter case cover by hooking
the holders onto the cover.

12. Place the hoses in their original position as

shown.

1. Air filter case cover

U1DT60E0.book  Page 41  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands