manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 144

8-55

8

EBU25051

Lubricating the rear knuckle pivots 

The rear knuckle pivots must be lubricated at the
intervals specified in the periodic maintenance and
lubrication chart.
Lubricate the pivoting points using a grease gun.

EBU25103

Lubricating the steering shaft 

The steering shaft must be lubricated by a Yamaha
dealer at the intervals specified in the periodic
maintenance and lubrication chart.

EBU29047

Battery 

This model is equipped with a VRLA (Valve Regu-
lated Lead Acid) battery. There is no need to check
the electrolyte or to add distilled water. However,
the battery lead connections need to be checked
and, if necessary, tightened.

NOTICE

ECB00620

Never attempt to remove the battery cell seals,
as this would permanently damage the battery.

Recommended lubricant:

Lithium-soap-based grease

1. Grease nipple

Recommended lubricant:

Lithium-soap-based grease

U1DT60E0.book  Page 55  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands