manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 131

8-42

8

13. Install the panel.

TIP

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the throttle body and the rubber joint mani-
fold fittings for an air-tight seal. Tighten all fittings
securely to avoid the possibility of unfiltered air en-
tering the engine.

EBU27812

Cleaning the spark arrester 

Select a well-ventilated area free of combustible
materials and make sure the exhaust and muffler
are cool.

1. Remove the bolts.

2. Remove the tailpipe by pulling it out of the

muffler, and then remove the gasket.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

1. Hose

1

1. Bolt

U1DT60E0.book  Page 42  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands