manualshive.com logo in svg

Yamaha grizzly 700, Owner'S Manual

Share
Download
Yamaha grizzly 700 Owner'S Manual Download Page 134

8-45

8

The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

4. Tighten the locknut.

5. Slide the rubber cover to its original position.

EBU24060

Valve clearance 

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU24071

Adjusting the drive select lever safety 
system cable 

The drive select lever safety system cable stretch-
es with use, which can result in improper function.
Therefore, the safety system cable should be
checked and adjusted by a Yamaha dealer at the
intervals specified in the periodic maintenance and
lubrication chart.

EBU29601

Brakes 

Replacement of brake components requires pro-
fessional knowledge. Brake service should be per-
formed by a Yamaha dealer.

1. Rubber cover
2. Throttle cable free play adjusting bolt

3. Locknut

4. Throttle cable free play

2WD

4WD

3

2

1

4

(b)

(a)

U1DT60E0.book  Page 45  Wednesday, March 3, 2010  2:51 PM

Summary of Contents for grizzly 700











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands