Yamaha grizzly 700 Owner'S Manual Download

Page: 160 / 170

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

2065 mm (81.3 in)

Overall width:

1180 mm (46.5 in)

Overall height:

1240 mm (48.8 in)

Seat height:

905 mm (35.6 in)

Wheelbase:

1250 mm (49.2 in)

Ground clearance:

275 mm (10.8 in)

Minimum turning radius:

3200 mm (126 in)

Weight:

With oil and fuel:

294.0 kg (648 lb)

Noise and vibration level:

Noise level (77/311/EEC):

YFM7FGPA 78.8 dB(A)@2965 r/min
YFM7FGPHA 78.8 dB(A)@2965 r/min
YFM7FGPSEA 78.8 dB(A)@2965 r/min

Noise level 40 CFR Part 205 Subpart D (Acceleration):

YFM7FGPA 78.5 dB(A)
YFM7FGPHA 78.5 dB(A)
YFM7FGPSEA 78.5 dB(A)

Vibration on seat (EN1032, ISO5008):

YFM7FGPA Will not exceed 0.5 m/s²
YFM7FGPHA Will not exceed 0.5 m/s²
YFM7FGPSEA Will not exceed 0.5 m/s²

Vibration on handlebar (EN1032, ISO5008):

YFM7FGPA Will not exceed 2.5 m/s²
YFM7FGPHA Will not exceed 2.5 m/s²
YFM7FGPSEA Will not exceed 2.5 m/s²

Engine:

Engine type:

Liquid cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

686 cm³

Bore

stroke:

102.0

84.0 mm (4.02

3.31 in)

Compression ratio:

9.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Recommended brand:

YAMALUBE

U1DT60E0.book Page 1 Wednesday, March 3, 2010 2:51 PM

Summary of Contents for grizzly 700











































































































































































Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands

Yamaha grizzly 700, Owner'S Manual

Search results

Summary of Contents for grizzly 700

Reviews:

Related manuals for grizzly 700

Brands by name

Popular brands