Yamaha F9.92D Owner'S Manual Download Page 84 | Manualshive

Page: 84 / 92

background image

Trouble Recovery

79

7.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope around the fly-
wheel several turns clockwise.

8.

Pull the rope slowly until resistance is
felt.

9.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29783

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

2.

Remove the spark plug(s), then face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

3.

Drain the fuel from the carburetor, fuel
filter, and fuel line. Drain the engine oil
completely.

4.

Fill the sump with the fresh engine oil.

5.

Feed engine fogging oil or engine oil
through the carburetor(s) and spark plug
holes while cranking the engine with the
manual starter or emergency starter
rope.

6.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor

until it has been completely inspected.

ZMU02333

ZMU02074

Engine oil capacity:

1.0 L (1.06 US qt) (0.88 Imp.qt)

«
...
82
83
84
85
86
...
»

Summary of Contents for F9.92D





























































































Reviews:

No comments

Related manuals for F9.92D

Brand: Panasonic Pages: 26

Brand: IEI Technology Pages: 12

Brand: IEI Technology Pages: 190

Brand: IEI Technology Pages: 8

Brand: IEI Technology Pages: 193

Brand: IEI Technology Pages: 182

KINO-DBT Series

Brand: IEI Technology Pages: 133

Brand: Aeroflex Pages: 20

35891900 Series

Brand: PC Partner Pages: 16

Brand: MSI Pages: 69

EMB-APL1-A10-3350-F1-LV

Brand: Aaeon Pages: 42

Brand: Texas Instruments Pages: 21

NORA-W10 Series

Brand: Ublox Pages: 22

MPG Z390 GAMING EDGE AC

Brand: MSI Pages: 87

Brand: Tadao Pages: 3

Brand: Intel Pages: 74

NB-IoT Module Series

Brand: Quectel Pages: 31

Fatal1ty B150 Gaming K4

Brand: ASROCK Pages: 154

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands