manualshive.com logo in svg

Yamaha F9.92D, Owner'S Manual

Share
Download
Yamaha F9.92D Owner'S Manual Download Page 51

 

Operation

 

46

 

2.

Place the tilt lock lever in the release/up
position.

3.

Slightly tilt the outboard motor up. The
tilt support bar will lock automatically,
supporting the outboard motor in a par-
tially raised position.

NOTE:

 

This outboard motor has 2 positions for shal-

 

low water cruising.

4.

To return the outboard motor to the nor-
mal running position, place the gear shift
lever in neutral, then place the tilt lock le-
ver in the lock/down position.

5.

Slightly tilt the outboard motor up until
the tilt support bar automatically returns
to the free position.

6.

Slowly lower the outboard motor to the
normal position.

 

EMU28090

 

Power trim and tilt models / power tilt 
models

 

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

 

EWM00660 

 

●

 

Place the gear shift in neutral before
setting up for shallow water cruising.

 

●

 

Return the outboard motor to its normal
position as soon as the boat is back in

 

deeper water.

CAUTION:

 

ECM00260 

 

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

 

ing can result.

 

EMU28184

 

Procedure for power trim and tilt / power
tilt models

 

1.

Place the gear shift lever in neutral.

N

ZMU04881

ZMU02044

ZMU02048

Summary of Contents for F9.92D





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands