manualshive.com logo in svg

Yamaha F9.92D, Owner'S Manual

Share
Download
Yamaha F9.92D Owner'S Manual Download Page 27

 

Basic components

 

22

 

EMU26360

 

Power tilt unit

 

This unit tilts the outboard motor up and
down and is controlled with the power tilt
switch.

CAUTION:

 

ECM00630 

 

Do not step on or exert pressure on the
power tilt motor. The power tilt unit could

 

be damaged as a result.

 

EMU26372

 

Top cowling lock lever(s) (turn type)

 

To remove the engine top cowling, turn the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling again by returning the lever(s) to the
lock position.

 

EMU26460

 

Flushing device

 

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

 

For details on usage, see page 54.

 

EMU26300

 

Warning indicator

 

If the engine develops a condition which is
cause for warning, the indicator lights up. For
details on how to read the warning indicator,
see page 23.

 

1. Power tilt unit
2. Power tilt motor

ZMU02078

 

1. Top cowling lock lever(s)

1. Flushing device

ZMU02009

1

1

ZMU04885

Summary of Contents for F9.92D





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands