Yamaha F9.92D Owner'S Manual Download Page 77

Page: 77 / 92

Maintenance

minal.

EMU29370

Disconnecting the battery

Disconnect the BLACK cable from the NEG-
ATIVE (-) terminal first. Then disconnect the
RED cable from the POSITIVE (+) terminal.

EMU29390

Checking top cowling

Check the fitting of the top cowling by push-
ing it with both hands. If it is loose have it re-
paired by your Yamaha dealer.

EMU29400

Coating the boat bottom

A clean hull improves boat performance. The
boat bottom should be kept as clean of ma-
rine growth as possible. If necessary, the
boat bottom can be coated with an anti-foul-
ing paint approved for your area to inhibit

marine growth.
Do not use anti-fouling paint which includes
copper or graphite. These paints can cause
more rapid engine corrosion.

1. Red cable
2. Black cable
3. Battery

ZMU02068

ZMU01943

Summary of Contents for F9.92D





























































































Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands

Yamaha F9.92D, Owner'S Manual

Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands