Yamaha F9.92D Owner'S Manual Download Page 48

Page: 48 / 92

Operation

Press the power trim and tilt switch /
power tilt switch “

” (up) until the out-

board motor has tilted up completely.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

sure.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods

ZMU02042

ZMU02823

ZMU04900

ZMU04884

Summary of Contents for F9.92D





























































































Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands

Yamaha F9.92D, Owner'S Manual

Search results

Summary of Contents for F9.92D

Reviews:

Related manuals for F9.92D

Brands by name

Popular brands