Yamaha F9.92D Owner'S Manual Download Page 75 | Manualshive

Page: 75 / 92

background image

Maintenance

70

suction pipe) in a suitable cleaning sol-
vent. Allow the filter to dry.

5.

Replace the gasket with a new one. Re-
install the fuel joint assembly and tighten
the screws firmly.

EMU29312

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

CAUTION:

ECM00720

Do not paint anodes, as this would render

them ineffective.

NOTE:

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-

er unit.

EMU29320

Checking battery (for electric start
models)

WARNING

EWM00330

Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is
poisonous and highly caustic.
Always follow these preventive mea-
sures:

●

Avoid bodily contact with electrolytic
fluid as it can cause severe burns or
permanent eye injury.

●

Wear protective eye gear when han-
dling or working near batteries.

Antidote (EXTERNAL):

●

SKIN - Flush with water.

●

EYES - Flush with water for 15 minutes
and get immediate medical attention.

Antidote (INTERNAL):

●

Drink large quantities of water or milk

ZMU02067

ZMU02924

«
...
73
74
75
76
77
...
»

Summary of Contents for F9.92D





























































































Reviews:

No comments

Related manuals for F9.92D

Brand: Intel Pages: 76

Brand: Gigabyte Pages: 36

Brand: IEI Technology Pages: 17

Brand: Raptor Pages: 59

Brand: Sure Electronics Pages: 32

LCD Programmer Module

Brand: Xtralis VESDA Pages: 54

Brand: ECS Pages: 92

Brand: Maxtang Pages: 13

Brand: ON Semiconductor Pages: 22

Brand: ASROCK Pages: 244

Brand: Texas Instruments Pages: 20

Brand: EPOX Pages: 64

DG31GL - Desktop Board Essential Series Motherboard

Brand: Intel Pages: 72

Brand: ASROCK Pages: 65

Brand: ASROCK Pages: 160

Brand: NXP Semiconductors Pages: 138

Brand: TYAN Pages: 54

Brand: TYAN Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands